Look up at many older roofs in Surrey and you will see the same problem: cracked, crumbling or missing mortar along the ridge at the top of the roof and down the gable ends (the verges). Loose mortar lets water in, allows tiles to work loose and, in high winds, can lead to ridge tiles falling from the roof.
Modern dry ridge and dry verge systems solve this by fixing tiles mechanically instead of relying on mortar. In this guide, our ridge tile and dry verge specialists explain how these systems work, their benefits and when you should consider an upgrade.
What Are Ridge Tiles and Verges?
- Ridge tiles are the curved or angled tiles that cap the very top of a pitched roof where the two slopes meet.
- Hip tiles do the same job along the sloping edges where two roof slopes meet on a hipped roof.
- Verges are the edges of the roof at the gable ends, where the tiles finish over the wall.
Traditionally, ridge and hip tiles were bedded in sand and cement mortar, and verges were finished with a mortar fillet between the tiles and an undercloak board.
Why Does Mortar Fail?
- Weathering – years of rain, wind and sun gradually erode mortar
- Freeze–thaw – water in small cracks freezes, expands and breaks the mortar apart
- Movement – roofs move slightly with temperature and wind; rigid mortar cracks rather than flexes
- Poor mixes – mortar that was mixed too weak or too strong fails sooner
Mortar ridges and verges commonly need repointing or rebedding after 15 to 25 years, and loose ridge tiles are one of the most common callouts after storms. If you have noticed debris in your gutters or on the ground, read the most common signs that a roof needs repair.
What Is a Dry Ridge System?
A dry ridge system replaces the mortar bed with a mechanical fixing kit. Typical components include:
- A ridge batten fixed to the top of the rafters with brackets
- A breathable roll-out ridge strip that seals against the tiles while allowing air to flow
- Ridge tile clips or screws that fix each ridge tile securely to the batten
- Union pieces that seal the joints between ridge tiles
- End caps to finish the ends neatly
What Is a Dry Verge System?
A dry verge system uses interlocking plastic caps (usually uPVC) fitted over the end of each row of tiles along the gable. Each unit is fixed to the end of the battens, creating a continuous, secure and weatherproof edge with no mortar.
Crumbling Mortar on Your Roof?
We upgrade ridges, hips and verges to secure, maintenance-free dry fix systems across Surrey. Ask for a free roof inspection and quote.
Get a Free Quote →Call 07311 065 336Benefits of Dry Ridge and Dry Verge Systems
- Secure fixing – every tile is mechanically fixed, greatly reducing the risk of storm damage
- Low maintenance – no mortar to crack, crumble or need repointing
- Weatherproof – designed to keep out wind-driven rain
- Improved ventilation – many dry ridge systems include ventilation, helping reduce condensation in the loft
- Flexible – components accommodate small roof movements without cracking
- Neat appearance – clean, uniform lines along the ridge and gable
- Pest protection – properly sealed verges stop birds nesting in gaps
Dry Fix Systems and BS 5534
BS 5534 is the British Standard code of practice for slating and tiling. Since its 2014 revision, mortar alone is no longer considered a sufficient fixing for ridge, hip and verge tiles – they must also be mechanically fixed. Dry fix systems are one of the most common ways to meet this requirement on new roofs and re-roofs.
If you are planning re-roofing or a new roof installation, dry fix ridges and verges will normally be part of the specification.
Can Dry Fix Be Added to an Existing Roof?
Yes. Dry ridge and dry verge systems can usually be retrofitted to an existing tiled roof without replacing the whole roof. The process typically involves:
- Setting up safe access with scaffolding or a tower
- Carefully removing the old ridge tiles and mortar
- Cleaning and reusing sound ridge tiles, or replacing damaged ones
- Fitting the ridge batten, ventilated seal and clips
- Removing old verge mortar and fitting the dry verge units
- Clearing all debris from the roof and gutters
Retrofitting is often done at the same time as other work, such as replacing fascias and gutters, to make the most of the access – see our fascias and gutters service.
Dry Fix or Repointing: Which Is Better?
Rebedding and repointing in mortar can be cheaper in the short term and may be preferred on some older or listed properties where appearance must be preserved. However, it will need doing again in future. For most homes, a dry fix system offers better long-term value and peace of mind.
Signs Your Ridge or Verge Needs Attention
- Cracked, crumbling or missing mortar
- Ridge tiles that look uneven or have moved
- Pieces of mortar in gutters or on the ground
- Gaps at the gable ends where birds are getting in
- Damp patches in the loft near the ridge or gable wall
Damp is also a sign of other problems – see Why is my roof leaking? 10 common causes.
What Affects the Cost of a Dry Fix Upgrade?
- The length of the ridge and any hips
- The number and length of verges (gable ends)
- Access requirements, such as scaffolding
- Whether ridge tiles can be reused or need replacing
- The condition of the battens and underlay at the ridge and verges
- Whether other work, such as gutter or fascia replacement, is carried out at the same time
If your roof has wider problems such as slipped tiles, failing underlay or widespread leaks, a full re-roof may be the better investment. Our guide How do I know if my roof needs repair or replacement? can help you decide.
Dry Ridge and Dry Verge FAQs
How long does a dry ridge system last?
Quality dry fix systems are designed to last for decades with little or no maintenance, far longer than traditional mortar.
Are dry verge systems suitable for all roofs?
They suit most concrete and clay tiled roofs. Some slate roofs and heritage properties may need a different detail. We will advise during the inspection.
How long does it take to fit?
A typical house can usually be completed in a day or two once access is in place, depending on the length of ridge and number of verges.
What if a ridge tile has already come off in a storm?
Call our emergency roofing team to make the roof safe and watertight, then consider a dry fix upgrade to prevent it happening again.
Related Guides
Upgrade to Dry Ridge & Dry Verge in Surrey
Say goodbye to crumbling mortar. Our experienced roofers fit secure, low-maintenance dry fix systems on homes across Surrey, Sussex and South West London.
Request Your Free Quote →📞 07311 065 336Based in Godalming and covering Guildford and towns across Surrey, Sussex & South West London.